Moment of Inertia of a flywheel by falling weight method
moment of inertia of a flywheel
EXPERIMENT : To determine the moment of inertia (MOI) of flywheel by falling weight method
Apparatus Required:
1. Flywheel 2. String 3. Stop-watch
4.Vernier caliper 5. Meter ruler 6. Slotted mass on hanger
THEORY :
Flywheel is a solid disc mounted on the shaft of machines such as turbines, steam engines, diesel engines etc. When the load of such machines suddenly increases or decreases its function is to minimize the speed fluctuations which occurs during the working of machines.The Flywheel acquires kinetic energy from the machines.The capacity of storing of KE (kinetic energy) depend on the rotational inertia of the flywheel.This rotational inertia is called as Moment of Inertia of rotating object namely wheels.
The moment of inertia of body is defined as the measure of object’s resistance to the changes of its rotation.
In this experiment, the flywheel rotates freely about a horizontal axis. The radius of the axie of the flywheel can be measured with a caliper. As ( m ) falls, its gravitational potential energy (PE) is transferred into translational kinetic energy of m, rotational kinetic energy of the flywheel and work done by friction. As the flywheel completes N further turns, its original rotational kinetic energy is transferred into friction loss.
For the known mass density & geometry of the material used, in SI system of units the unit of moment of inertia is Kg.m2 (kilogram meter square)
Procedure to perform the Experiment :
1. The flywheel is set with the axle of the flywheel horizontal. A polystyrene tile was placed on the floor to avoid the impact of the mass on the floor.
2. The vernier caliper is used to measure the diameter d of the axle. The mean of two perpendicular measurements was taken.
3. The hanger with appropriate amount of slotted mass is put on the tile. Which is used the balance to measure the total mass m.
4. The mass is winded to an appropriate height. Verified that the string fell off the axle when the mass hit the ground.
5. The height h of the mass is measured. The height h was recorded.
6. The mass is released then and at the same time the stop-watch is started.
7. As soon as the mass hit the ground, timing was stopped and the number of revolution the wheel revolved is taken.
8. The mass is winded up again and steps are repeated for at least 3 times.The mean time of the falling is obtained.
PRECAUTIONS :
1. Do not stand too close to the polystyrene tile when releasing the mass.
2. The turns of the string must not overlap the other.
3. Stop Watch must be handled with care in order to avoid any error in the reading.
4. The first few turns of the string should overlap the others.
5. The mass should be wound up to the same height in all trials.
Some Important questions and answers related to the Experiment:
Q: What do you understand by MOI ?
Ans: MOI stands for moment of inertia.It is a quantity expressing body’s tendency to resists angular acceleration.
Q: Give the expression for the MOI of Flywheel.
Ans: mgh = ½ mv2 + ½ Iω2 + n1E
Q: Draw the labelled diagram of Flywheel setup for calculation of MOI ?
Ans:
Q: List the apparatus required in the experiment ?
Ans: 1. vernier caliper
2. Flywheel
3. string
4. meter ruler
5. Stop watch
6. slotted mass on hanger.
31 Responses to Moment of Inertia of a flywheel by falling weight method
« Properties and uses of PMMA (high polymer) The Law of Parallelogram of Forces »
Bsc 1 year
None
None
viva questions and answers on flywheel
Fly wheel experiment
Viva question related to fly wheel
Bsc 1st yr
velocity
1st Bsc
Moment of inertia of flywheel with experiment
Enter your any educational query or doubt polytechnic
what are the number one books a i.m.sc student of 1st year should refer to increase his knowledge
What are any possible suggested systematic errors that would produce effects consistent with observed difference between the experimental and theoretical values for the moments of inertia.
how to find mass moment of inertia of different as the radius changes with mass
1. theory of machines solved questions
2.electrical engineering machine solved questions
3. surveying solved questions
moment of inertia of a flywheel and a falling weight